Browse all practice questions for the Power and Performance III Tuners Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Power and Performance III Tuners Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What is the role of lines in the fuel system?
  • TPS stands for which sensor?
  • Which type of air filter uses metal wool in oil and filters dirt through capillary action?
  • Which statement about engine management system components is true?
  • The BARO sensor makes up for altitude by either adding or subtracting from the base duty cycle.
  • Which action would you use to share a calibration with another person?
  • What value indicates when the vehicle has warmed enough for the PCM to operate in closed-loop?
  • Which component controls the RFI and also improves the spark at high voltages?
  • Which feature provides quicker spool time due to lower drag on the shaft?
  • A piggyback ignition module would most likely modify the signal from the PCM to control __________.
  • If fuel rail pressure is suspected to be too high, which component should be checked?
  • Which device controls TV pressure in modern vehicles?
  • Check for updates to the tuning software before connecting it to the vehicle.
  • The runner directs the bouncing air back to the intake valve.
  • The _______ has a longer insulator tip and the heat travels a longer path.
  • The following should be scaled down at the same rate as airflow:
  • The Roots supercharger provides the highest thermal efficiency of any supercharger design.
  • If you calibrate the cam gear to the ___________ setting, you will move the torque curve to a lower rpm range than stock.
  • Air density is determined by the number of air molecules per unit volume.
  • You should calibrate the PCM's Closed-Loop parameters for vehicle cruising after initial startup.
  • TP data indicates the amount of vacuum in the engine.
  • Which component directs the bouncing air back to the intake valve?
  • Which limiter limits the spark and then the fuel?
  • In the _________ ignition system, one coil fires all spark plugs.
  • SCT uses a handheld controller that interfaces between the stock PCM and the laptop.
  • Which sensor measures the mass of air entering the engine?
  • The throttle body that is commonly referred to as drive-by-wire is which type?
  • In the N/V parameter, V stands for which?
  • Which timing parameter can be adjusted with 0 to 6 degrees of crankshaft timing per cylinder?
  • Which term describes the PCM's adjustments during start-up and open loop?
  • What speed is necessary for the PCM to switch to Closed-Loop mode?
  • A data logger can record live sensor values.
  • In the presence of a boost leak, which MAP reading scenario is most likely?
  • The PCM uses a set throttle position during open-loop idle.
  • Draw-through sensors are typically used in naturally aspirated engines.
  • Which sensor adjusts the base duty cycle based on intake air temperature?
  • Which component is used to cool compressed air in many forced-induction systems?
  • Which rev limiter cuts out spark at specific points to hold the engine RPM?
  • Which sensor typically does not require signal conditioning before sending its signal to the engine control module?
  • Do timing control modules have coils in the module to control ignition timing?
  • Which retard function is used in nitrous oxide and boost applications to activate the retard function?
  • When the PCM detects a concern through the knock sensor, it commands __________ until the knock stops.
  • Which type of air filter uses oiled cotton gauze with aluminum wire mesh for increased filtering capabilities?
  • Which action allows the technician to use another PCM's calibration?
  • Use an electrically driven water pump.
  • With reduced boost due to a leak, which manifold pressure pattern would you expect?
  • Which term describes the timing advance removed to compensate for increased pressures?
  • The Roots supercharger is an external compression supercharger.
  • You should place the stock camshaft gear at __________ when preparing to install an aftermarket adjustable camshaft gear.
  • Which component controls the fuel delivery, ignition system, and firing order?
  • The throttle position sensors that are 0-5 volt sensors and are typically not adjustable are which type?
  • Preset calibrations often come with tuning software.
  • PIDs can be retrieved with a scan tool or a data logger.
  • Tuning software can only tune the air/fuel ratio for open loop operation.
  • Which type of intercooler circulates water through the tubes?
  • The PCM advances the spark timing upon engine startup.
  • A __________ uses exhaust energy to increase the density of incoming air.
  • Retarding spark timing increases torque and horsepower.
  • An IAC valve allows air to bypass the throttle plate.
  • AR in turbocharger terminology stands for area to radius ratio.
  • Which sensor type uses a wire coiled around a permanent magnet?
  • The ________ indicates the amount of energy in the fuel used by the engine.
  • Which component has larger area and shorter length runners to maximize airflow?
  • If a boost leak causes a lean condition, what would be the expected trend in fuel trims?
  • A data logger can record live sensor values.
  • In high performance applications, ductwork is sized to maintain air speeds between 200 and 300 feet per second.
  • The logging rate is the length of time that the data logger can record vehicle data.
  • Which type of air filter uses thick foam and honeycomb networks to trap dust particles?
  • Adjusting the ________ table allows the upshifts and downshifts to occur at vehicle speed values.
  • A __________ induction system uses a forward-facing scoop and pressure created by the vehicle's movement to increase static air pressure.
  • You should calibrate the PCM's __________ parameters for vehicle start-up and wide open throttle.
  • If the STFT adjustments reach the set limit, a DTC will be recorded.
  • Which action would you use to create a new calibration from scratch?
  • Which sensor reading would most directly indicate a boost leak is present?
  • After the PCM resolves a knock issue, it commands __________ in small increments.
  • The Intelligent Ignition System is capable of controlling ignition timing and phase angle.
  • Using mechanically driven components has what effect on parasitic drag?
  • By reducing ______ through smaller or lighter parts, you can reduce the turbo lag of the turbine.
  • For accurate MAF transfer, correct base ______ amounts must be set for idle, part throttle, and wide open throttle.
  • What is the most likely cause of the concern indicated by the PID?
  • If the ______ is too large, it may reduce the turbo response causing turbo lag.
  • Which component corresponds to the turbine location in a turbocharger?
  • In a turbocharger, fresh air enters which housing?
  • Hondata interfaces between a replacement PCM and the laptop.
  • Relative to ambient, what happens to MAP pressure when boost is diminished by a leak?
  • The throttle body that operates by linkage connected to the accelerator pedal is which type?
  • Preset calibrations often come with tuning software.
  • The injector duty cycle is the amount of pressure exerted by the fuel injector.
  • PIDs retrieval is possible with which tools?
  • Which drive options are used for some superchargers depending on the application?
  • The _______ function tells the control module at what speed to lock and unlock the torque converter.
  • What is the most likely cause of this concern?
  • The anti-surge valve increases the boost and is used in Roots superchargers.
  • Which end is described as angled end?
  • Which component modulates the torque converter clutch to achieve a firmer engagement?
  • In aftermarket setups, what component is located between the production PCM and the control device or sensor?
  • Which end does not include a ground electrode?
  • Bypass the A/C compressor has what effect on parasitic drag?
  • Which term is used for the graph that shows engine torque across operating conditions?
  • What is the additional fuel the PCM commands during open-loop startup?
  • If the ________ provides an incorrect signal to the control module, shift points will occur at the wrong road speed.
  • Which part is affected by the combustion chamber design?
  • What is the lowest engine temperature at which the PCM will not switch to open-loop?
  • Which action allows the technician to view an existing calibration?
  • Which action allows the technician to share a calibration with someone else?
  • The cold air induction system is based on the theory that cold air has __________ density.
  • Which component may be replaced when installing Roots or screw-style superchargers?
  • A seized turbocharger is caused by boost pressure leaks.
  • Which component failure commonly creates a boost leak leading to a low MAP reading?
  • Duty cycle is the percentage of injector on-time.
  • Before installation, why is surface area an important consideration?
  • Which describes the role of dowel pins when mounting an intake manifold to the cylinder head?
  • The controller in an Intelligent Ignition System charges and discharges the capacitor once across multiple crankshaft degrees.
  • Which component is used to regulate engine idle speed by adjusting the air bypass around the throttle?
  • Tuning software adapts to the type of computer you use.
  • Which statement about piggyback controllers is true?
  • Which device is often used in GM vehicles?
  • Which term describes the maximum degrees the PCM will advance the timing?
  • In a compound turbocharger setup, are the two turbochargers typically identical in size?
  • The __________ coil handles a high voltage of 500V-600 volts on the primary side.
  • What is the primary function of regulators in a fuel system?
  • In the __________ coil, there is one coil per cylinder.
  • Decrease the crankshaft pulley diameter.
  • Flow boosters ease the transition around sharp edges and reduce turbulence.
  • The ______ is measured in CFM.
  • True or false: Saturated circuit injectors measure between 2 and 6 ohms.
  • If you experience noise, check the intercooler fins.
  • Exchanging a pulley for one with a different diameter changes the __________.
  • Large throttle bores are preferred because of the turbulence they create.
  • The centrifugal supercharger is similar to the turbocharger induction system.
  • High-performance engines that produce maximum torque at high speed use which type of runners?
  • Use iron pulleys.
  • The coolant flowing through the throttle body prevents icing.
  • The PCM opens the throttle plate further when the engine is warm than when it is cold.
  • Which outcome may occur if the TPS voltage exceeds a certain limit?
  • Which action allows the technician to view the calibration later?
  • Twin turbocharger system uses two identical sized turbos matched with 1/2 of the engine's need. Technician B says that compound turbochargers use turbochargers that are the identical size. Which technician is correct?
  • If you replace the stock camshaft with a high performance camshaft, you should adjust the target idle speed.
  • The MAF sensor can have adjustable calibration settings.
  • Which statement about the Intelligent Ignition System’s voltage handling is supported by the material?
  • Low boost in a turbocharged engine can be caused by excessive bearing drag.
  • TV pressure in modern vehicles is controlled by which component?
  • Which statement about street-use intercoolers is correct?
  • For accurate MAF transfer, which statement is correct?
  • The opening of the turbine housing where the exhaust gases enter is called the Inducer.
  • MAF transfer data is the relationship of ______ flow as it corresponds to the MAF sensor signal voltage.
  • The twin-screw supercharger has identical rotors.
  • Airflow is measured in cubic centimeters.
  • Which end has electrode and insulator sticking above the shell?
  • Which diagnostic signal most directly points to a boost leak as the cause of low boost?
  • Brake Specific Fuel Consumption (BSFC) expresses fuel consumption as what unit?
  • Which sensor converts knock vibrations into electrical signals?
  • Moving the cam gear to the retard setting shifts the torque curve toward higher RPMs.
  • In compressor map discussions, Technician A claims choke lines indicate efficiency drops, Technician B claims turbo speed lines represent constant speed. Which technician is correct?
  • BSFC calculations help determine how much fuel is required to get the desired horsepower per hour.
  • Which limiter limits the fuel and then the spark?
  • Advancing the timing too far can cause engine damage.
  • Which tuning software requires typing in a processor code to create a new calibration?
  • WOT shifts occur based primarily on which parameter?
  • For street use, which intercooler type is most effective?
  • Pressure ratio is the density ratio divided by horsepower.
  • Which filter type uses oiled gauze with aluminum wire mesh?
  • When running on low-octane fuel, ignition timing should be.
  • Which term best describes 'the rate of timing advance' in engine control terminology?
  • Which sensor adjusts base duty cycle in response to ambient air pressure to compensate altitude?
  • Which parameter group includes options to enable and disable the torque converter clutch?
  • What term describes the rate at which the PCM decreases the signal for additional fuel during open-loop startup?
  • Before calibrating idle speed control, make base calibration adjustments.
  • If the boost leak is corrected, what is the expected MAP reading trend?
  • The tapered runner angle is ____________ at the plenum.
  • Which technician is correct about performance applications and centrifugal superchargers?
  • Which action allows the technician to program a new calibration?
  • If boost pressure is significantly reduced due to a leak, the MAP reading will be
  • The crankshaft-driven ______ adds power by increasing the density of the air.
  • The ______ must be correct because fuel and spark tables use calculated load as a primary input.
  • The boost retard system activates a different amount of retard for each gear.
  • Before installing adjustable cam gears, you may need to perform which operation?
  • To know what to change about the idle speed calibration, observe an idle speed data log.
  • Scaling can correct for the 'pegging the meter' concern that may occur during which conditions?
  • Technician A says that advancing cam timing increases lower-end torque improves idle, drivability, and emissions. Technician B says that retarding the timing can increase horsepower and torque at lower speeds. Which technician is correct?
  • Which statement about volumetric efficiency (VE) is true?
  • MSD manufactures replacement ignition systems for Mercedes, BMW, and Ferrari.
  • Which technician correctly described which factor can cause oscillations in the data log during idle?
  • Which description matches SCT?
  • Technician A says poor idle drivability can result from mechanical failures, electrical opens or shorts, or improper tuning calibrations. Technician B says that during idle the PCM commands spark advance for low-end torque. Which technician is correct?
  • includes parameters to modify shift pressure
  • Which term provides a user-friendly interface that allows tuning and diagnostics?
  • The PCM controls the powertrain management strategies.
  • Two-step launch control: Technician A says it must be enabled with a clutch pedal; Technician B says you must calibrate the PCM to hold RPM at a specific point. Which technician is correct?
  • What is the amount of time the PCM remains in open-loop when the engine is below a certain temperature?
  • The throttle position sensors that are usually adjustable are which type?
  • Which parameter governs the speed points where shifts occur?
  • The _______ has a shorter insulator and operates at low temperatures.
  • In the described voltage scenario, which statement is correct?
  • Drive power of the supercharger is calculated using boost pressure and which parameter?
  • Which tool is typically used to detect leaks in the intake system during diagnosis?
  • By altering the length of the runner, you can optimize the resonance effect.
  • Which component has excellent airflow capacity and filters small and large particles?
  • Under heavy load, which spark timing adjustment is typically used?
  • An example is two-step launch control.
  • Which type of air filter offers the greatest protection in trapping dirt particles?
  • includes parameters for adjusting shift points
  • In timing control, 'initial spark timing' refers to the timing adjustments during start-up and open loop.
  • The ______ streamlines airflow through the core.
  • includes parameters to enable and disable the torque converter clutch
  • Which statement is correct about fuel calculations and injector sizing? Technician A says calculating the amount of fuel an engine needs helps determine the injector size. Technician B says BSFC calculates how much fuel is required to achieve the desired horsepower in a one-hour period.
  • The ______ mounts on the intake system between the turbocharger and throttle body and prevents the ducting from blowing apart.
  • Which component is made of plastic, aluminum, or carbon fiber?
  • What is the role of fittings in the fuel system?
  • Which component reduces noise and potential damage caused by surging?
  • HP Tuners is often used in GM vehicles and interfaces with a laptop to the stock PCM.
  • If there are 50 secondary turns for every one primary turn, the turn ratio will be ________.
  • Which tuning software must you open an existing calibration to create a new tune?
  • Low resistance injectors are also called peak and hold injectors.
  • Which statement about peak and hold injectors is true?
  • If you experience excessive boost, inspect the wastegate.
  • Which MAP reading would you expect when boost pressure is reduced by a leak?
  • The ______ represents the forward-facing surface area of the core.
  • Make idle control adjustments before calibrating base settings.
  • The intercooler allows you to run more ignition timing.
  • Which component controls the airflow into the intake manifold?
  • The inertia of air when the intake valve closes forms a pressure wave that travels back to the induction system.
  • Which tuning software can you create a new calibration from scratch by clicking New?
  • You can calibrate the PCM to command timing advance just before __________.
  • The multi-spark ignition system produces multiple sparks during each firing cycle.
  • The multi-spark ignition system is used commonly in stock applications.
  • Which PID in a cruise data log indicates a vehicle concern?
  • Which sensor measures the rotation angle of the throttle blade?
  • Decreasing the accessory pulley diameter results in what change to parasitic drag?
  • A bypass valve reduces heat and pumping loss from fixed displacement superchargers.
  • Replacing a cast iron pulley with an aluminum pulley is used to decrease what?
  • Superchargers are driven by the exhaust.
  • Which action would you use to open an existing calibration to edit?
  • Which device connects the ignition control module microprocessor with a USB cable?
  • You should advance the timing for forced induction engines to prevent detonation.
  • Which PID in this data log, taken during idle, shows a vehicle concern?
  • Parasitic drag is energy lost due to accessory components driven by the crankshaft.
  • Which retard function is programmed in increments from 0 to 15 degrees in 0.5-degree steps?
  • Which characteristic may cause preignition misfire, or fouling?
  • An excessive ______ reading may indicate a fuel calibration concern.
  • What is the expected effect on idle performance when cam timing is advanced?
  • The MAP sensor provides the PCM with boost pressure information.
  • Which factor primarily determines when to shift under wide-open throttle conditions?
  • MSD manufactures multi-strike sparks with greater burn efficiency.
  • Regarding air filter velocity for dirt removal, which statement is correct?
  • The MAP sensor provides the PCM with information about the manifold pressure.
  • The ________ testing determines where the electrode gap should face in the combustion chamber.
  • An underdrive pulley reduces __________.
  • The logging rate will vary by the tuning software.
  • The Intelligent Ignition System controller monitors the ignition current and the peak voltage to tailor spark to the cylinder.
  • Which type of intercooler gives heat to the outside air across the fins?
  • You would most likely want to use a piggyback controller when __________.
  • The ignition advance allows for richer air/fuel mixtures at start-up.
  • What term is recommended for a firmer torque converter clutch apply?
  • Adjusting the cam gear to the ___________ setting moves the torque curve to a higher rpm range than stock.
  • What should be calibrated by the manufacturer whenever fuel injectors are changed or airflow is modified?
  • If a performance vehicle has a 600 horsepower engine and uses 0.5 pounds of fuel per horsepower, with 6 cylinders and 6 injectors, how many pounds of fuel does it burn per hour?
  • Which statement about ignition spark cycles is true according to the material?
  • During closed-loop operation, the PCM may alter the throttle position to meet load demands.
  • Technician A says that the PCM will go into limp-home mode if both APP sensors become faulty. Technician B says the PCM may shut down the alternator if TPS voltage exceeds a certain limit. Which technician is correct?
  • You can change the __________ to bypass mechanically driven components.
  • Technician A says that piggybacks can modify the signal coming from the PCM to an actuator. Technician B says that a piggyback controller can be tuned to change the PCM's control strategy. Which technician is correct?
  • Which sensor may use two sets of slots to provide crankshaft position in degrees to the ignition module?
  • Adjustable cam gears often come in configurations such as 3-way or 9-way. Which option best describes this?
  • The ______ removes heat from the incoming air charge, before it enters the engine.
  • The _______ process positions the spark plug ground electrode in a specific area of the combustion chamber.
  • The component that detects combustion concerns through vibration.
  • Intercooling reduces __________, creating a powerful air/fuel charge.
  • What determines the mounting location of a supercharger?
  • Which prompts to save a calibration before exiting?
  • Technician A says that any sensor data recognized by a data logger can be recorded. Technician B says that the logging rate will vary by the tuning software. Which technician is correct?
  • Which observation would support a MAP reading being lower than normal due to a leak?
  • After adding ________, you improve the VE of the engine well over 100%.
  • Excessive boost in a turbocharged engine should be checked by inspecting the wastegate.
  • Blow-through sensors are located after the supercharger, turbocharger, or intercooler, just before the throttle body.
  • During port matching, which technician is correct about using dowel pins to index the intake manifold to the cylinder head?
  • Which component uses the MAF data to properly match the fuel output vs. the air/fuel ratio table?
  • Low boost can be caused by excessive bearing drag.
  • What is the typical effect of a boost leak on boost pressure and engine performance?
  • Knock may result from improper ______ calibration.
  • Adjustable cam gears contain bolts that can be loosened to adjust phasing. Which is the correct feature?
  • The shift light illuminates when the engine speed reaches preset maximum rpm.
  • Data loggers can record sensor data only if the logger recognizes that sensor.
  • An ammeter is used to directly measure the resistance on an injector.
  • In the ________ coil, there is one coil for every two cylinders.
  • The VE for a stock two-valve, four-stroke engine is 95%.
  • Which factor primarily affects spool time, making understanding turbo compressor maps important?
  • Engine management systems come with a replacement PCM and a wiring harness.
  • The ______ allows the system to run more ignition timing.
  • In a fixed amount of gas, when pressure increases, what happens to volume?
  • Which statement is correct regarding a hybrid turbocharger concept, where the stock turbine housing is kept and the compressor wheel trim is increased?
  • Hondata
  • In a turbocharged engine, a leak that causes boost to fall short of the target would affect the MAP sensor reading as which of the following?
  • Technician A says that changes in road surfaces can cause oscillations in the data log. Technician B says that the IAT data should always match the ECT data. Which technician is correct?
  • When calibrating adjustable cam gears, the __________ should be advanced or retarded for desired performance.
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy